Philips Capella 753/4E/3D – fr

Philips Capella 753/4E/3D capella 753 - fr

Philips Capella 753/4E/3D – fr

PHILIPS CAPELLA 753/4E/3D

PHILIPS CAPELLA 753/4E/3D

The Philips Capella 753/4E/3D was the company’s flagship model back in 1955, but in reality, the brand was working towards making it the best piece of technology to come out of Germany, blowing away the competition.

As a matter of fact, they met their goal and produced a unique piece of technology, for both the German and World Wide market.
It’s peculiarities are:

  • A motorized Tuning
  • 6 memorizable stations
  • 4 power tubes (2xEL84 and 2xUL84)
  • Dedicated amps for Hi and Low frequencies
  • An Iron-Free coupling output (OTL)
  • High Damping Factor with Negative Feedback circuit
  • 4 High impedance speakers

Even though the Philips Capella 753/4E/3D boasts a noticeable size, it’s woodwork, frames, and speaker covers contribute in giving it a much sleeker, eye-pleasing look to complete any furniture display.
The Low frequencies are particularly deep thanks to the separated OTL amplifiers and to the impressive size of the subwoofer, approximately 26cm in diameter (more or less 30 inches).
I suggest making good use of the mid-tweeter, as this successfully crafted speaker (17 cm in diameter) makes the mid and Hi frequencies pleasant and true to life, especially if seated in front of the Machine.

High and Mid Frequencies sections
The FM group is of the variable permeability type.
It has a high amplification and stability. Being equipped with an automatic noise suppressor in the presence of signals below 1.7 V, the output is muted to avoid hearing rustling and noise when searching for stations.
The de-emphasis circuit is set to 50 uS, valid all over the world except for the USA and South Korea. In these countries, the filter should be increased to 75 uS.

The AM section is equipped with a rotating antenna for the OM and OL bands. The antenna can be controlled by a knob on the front.
The mid-frequency sections are composed of three separate filters for AM and FM. The first of these filters is adjustable. The second is the amplifier filter and the third filter further increases the selectivity of the device.

The Motorized Tuning and the amplifier section are examined in detail in the following sections.

All the listed solutions translate into a very low distortion, an increase in power, and a pleasantness of use hardly ever obtained in other appliances.
This is the Philips Capella 753/4E/3D

Philips Capella 753/4E/3D
Philips Capella 753/4E/3D

BLUETOOTH

Bluetooth receiver embed

READ MORE >

MULTI PLATFORM CONNECTION

Each radio is equipped with a cable for connection to any digital device.

READ MORE >

TUBESOUND IMPROVEMENT

- Bluetooth receiver embed - The unit is equipped with a BLUETOOTH receiver powered directly by the receiver power supply. This makes it possible to control the amplifier from any external digital device as an IPAD, a Smartphone, or a sophisticated multimedia station. So you can hear your preferred web station or your lossesless file without cables on the room. Wireless Receiver can be equipped upon requests.

Multi Platform Connection – A customized adaptation cable to connect any digital device as Iphone, Smartphone, Laptop, CD Player etc. will be provided with this radio. This special cable suits the different impedances between the modern equipment and the receiver. Furthermore the two stereo channels flow into one without increasing the load to the input unit.

HISTORY

In 1891, the brothers Gerard and Anton Philips, started to produce the first incandescent bulbs in Eindhoven.
Later, Philips specialized in the production of electro- medical equipment, and in 1918 introduced the first X-ray tube.
In the following years, Philips began specializing in the broadcasting industry. In 1932 the company succeeded in selling over one million radio equipment and became the world’s first producer.
During the Second World War, Philips transferred to the Netherlands Antilles, and returned to the Netherlands at the end of the conflict.
In the second post- war period, began the production of the first televisions, then the launch of the music cassettes in 1963 and the production of the first integrated circuit in 1965.
In 1982 Philips launched with Sony the first compact disc player.
In 1984 Philips acquired the control of the German Grundig.
In the 90's Philips faced a financial crisis.
In 1991 it inserted on the market the Video CD and it is one of the first companies in the world to develop high definition television.
In 1999 Philips established a joint venture with LG Electronics, named LG Display, which ends in 2009.
In 2006 together with Sony launched the first Blu-ray.
In 2009 Phillips launched the first full-HD LCD TV in 21:9 format.
Phillips holds 48,000 registered patents.
Currently, the production is focused on low- energy lighting products and LED systems and services for diagnostics and production of medical devices.

MAIN FEATURES

Year of production: 1955
8 AM Circuits
12 FM Circuits
Wavebands:: LW, MW, SW, FM
Loudspeakers:
1 sub-woofer
1 mid-woofer
2 mid-tweeter
Operating voltage (CA): 110; 125; 220; 240 Volts
Dimensions (LHP): 700 x 455 x 275 mm / 27.6 x 17.9 x 10.8 inch
Net weight: 18 kg / 39 lb 10.4 oz
11 Tubes: ECC85 ECH81 EF89 EBF80 EM80 EABC80 EC92 EL84 UL84 EL84 UL84

Rotating ferrite aerial for AM bands

Ironless output

Philips Capella 753/4E/3D

Philips Capella 753/4E/3D
Philips Capella 753/4E/3D

AMPLIFIERS

The preamplifier consists of two stages. At the entrance, the volume potentiometer is equipped with three sockets for physiological correction (loudness). The intervention curves are visible in the first graph.
Philips considers the frequency of 800 Hz to be the center of the audible band, so the treble and bass controls are calculated to enhance the frequencies above and below that value. The choice of this frequency is very important for the musicality and the pleasantness perceived by listening to the device.
In the second graph the frequency response of the preamplifier, with the tones enhanced to the maximum. You notice the different equalization you get by listening to the AM bands (Long Waves, Medium, Short) or listening to the FM band and PHONO.

The final stages are two distinct, one for the low frequencies and one for the high frequencies. These amplifiers control separate speakers, a 26 cm woofer for the bass and three speakers for mid/high frequency, with the 17 cm front speaker disconnectable for 3D effect.
The most interesting feature of these final stages is that they are without an output transformer.

The feature that makes this device very interesting is that each final stage uses a pair of EL84 / UL84 in an ironless configuration, ie without an output transformer (the known critical point of the final stage).
The output stage uses the operating principle called Shunt Regulated Push-Pull (SRPP) used today in HIGH-END amplifiers.
The output transformer limits the bandwidth of the entire amplifier. The bass is limited by the inductance of the primary winding, the treble is limited by the parasitic capacitance resulting from the alternation of the primary and secondary windings. The alternating winding of the primary and the secondary windings is also necessary to improve the coupling and thus reduce the dispersed flow.
The reduction of the dispersed flow increases the damping. This is essential in the loudspeakers mounted inside the cabinet of the radios, which do not work in hermetically closed boxes, and which are therefore free to move almost without resistance from the surrounding air.

The two output tubes (EL84, UL84) of each channel, four final valves in total, are connected in series with DC-DC coupling. Each UL84 is configured as a triode.
The output is taken from the cathode of the UL84. The speaker has an impedance of 800 ohms, identical to the average impedance that occurs on the catode, whereby direct coupling (without transformer) is possible between the final stage and the loudspeaker.
The Philips Capella 753 is therefore totally free of all the problems deriving from the output transformers.

The damping of the loudspeakers is kept high by the low dynamic resistance of the feedback loop.

 

MOTORIZED TUNING AND PRESET MEMORY

Another feature of the Philips Capella 753/4E/3D is motorized tuning and preset memory.
Using 6 keys on the keyboard it is possible to memorize 3 FM stations, 2 in Medium Waves and 1 in Long Waves.
Pressing one of the storage keys via a cable pulls the lever H. The opposite side of that lever is pushed towards the disk R. This disk is divided into two parts with different diameters. Depending on how the disc is positioned, the lever H moves by activating a switch that turns the motor to the right or left until the lever H is fitted on the groove on the disc R. At this point, the motor stops. The R disks are rigidly connected to the axis A1 and through frictions to the R disk.

Tuning procedure

When a memory key is pressed, the motor will start to turn to the right or left according to the above.
Through the gears, Z1, Z2, Z4, Z5 the axis A1 is turned. Through the gears, Z6, Z7 the variable capacitor is rotated, which stops when the lever H engages in the groove of R.
To memorize a station, simply press the button on which it is to be stored, pull the tuning knob and turn it to the desired station.

Philips Capella 753/4E/3D

Philips Capella 753/4E/3D

TONE CONTROL WITH LEVEL INDICATION

The tones control system is very efficient.
Above the large tone control knobs there is two bands that lights up gradually indicating the emphasis on the band on which it acts.
The high-tone control knob is linked to two thin ropes. One of them is for the position indicator of the control itself, whereas the other changes the position of the ferrite in the MF transformers modifying the its curve.
By doing so high tones were attenuated/accentuated even before getting to the BF stage. 

Bass at max - Treble at max

Philips Capella 753/4E/3D

Bass at min - Treble at max

Philips Capella 753/4E/3D

Bass flat - Treble flat

Philips Capella 753/4E/3D

Bass at max - Treble at min

Philips Capella 753/4E/3D

Bass at min - Treble at min

Philips Capella 753/4E/3D

ANTENNE

Inside the cabinet there is a dipole for FM reception and a ferrite rotating aerial for AM reception.
Ferrite aerial can be rotated from the outside to achieve a perfect tuning of the device in the AM.
In this picture see the rotation mechanism and the position indicator of the aerial.
The reception sensitivity with internal aerials is very good. 
Using an external aerial sensitivity is further increased.

TUNING INDICATOR

The magic eye has of course been replaced.

Philips Capella 753/4E/3D

LOUDSPEAKERS

The 28 cm loudspeaker, with a 25 mm diameter magnetic core, is placed at the front.
A front 17 cm mid-tweeter can also be switched off if you want to increase the 3D effect.
On the two sides, there are two elliptical tweeters pointing upwards. Radiating to the ceiling of the room to take advantage of the reflections of the environment that add to the direct radiation produce an expansion of the soundstage.
There are no dangers of stationary wave due to the working frequency of these speakers.

There are several options for connecting external speakers.
It is, in fact, possible to connect an external woofer, excluding or not the internal woofer while leaving all the other speakers active.
It is possible to connect external medium-high units, excluding or not the internal mid-tweeters, while leaving the internal woofer active.
It is possible to connect woofers and external medium-high units, excluding or not all, or some, internal speakers.

CONTROL PANEL

Philips Capella 753/4E/3D

In the center of the speaker panel is the Magic Eye which indicates the perfect tuning of each station.
KLANGREGLER - Low Tone Indicator (FA Key) and High Tone Indicator (SOL Key).
Just below we find the large Volume knob, with built-in automatic loudness correction.
Coaxially you can see the 3 position Speaker Selector Lever (External Only - Indoor + Outdoor - Indoor Only)
Below we find the two coaxial knobs arranged horizontally, which respectively command the Bass Tones and the Treble Tones.
In the middle, we see the dial scale of the AM bands on a dark background (Long Waves - Medium - Short) and the dial scale of the FM band on a golden background.
FERROCEPTOR - Indicator of the position of the internal ferrite antenna. This internal antenna (excludable with the HA key) is used in the OM and OL bands. The internal antenna must be rotated until the best tuning is achieved.
Just below we find the large knob of the Manual Tuning, whose movement is very pleasant being supported by a large flywheel.
ZEIGER - Coaxially you can see the drive lever of the Motorized Tuning. It can be moved in the two directions, to the left or to the right.
Finally, underneath again we find the Rotation knob of the Ferrite Antenna.

To store a station you must:
1 - press the desired memory key.
2 - Pull the tuning knob and tune to your favorite station.
3 - Release the tuning knob.


Under the dials, we meet a long series of 14 keys.
Starting from the left the keys have the following functions:
OL memory
OM1 memory
OM2 memory
AUS - Switch off
3D - Excludes Mid / Front Tweeter by increasing the three-dimensional effect of the sound
HA - Outdoor / Indoor Antenna for OM and OL
LW - Long Waves
MW - Medium Waves
KW - Short Waves
UKW - FM
FM1 memory
FM2 memory
FM3 memory

REAR SIDE

Output for external speakers.
Socket for recorder (tonbandgerat).
Turntable input (Tonabnehmer)
AM and FM aerial inputs and ground socket.

Be careful: Use ONLY 800 ohm loudspeakers

RESTORING WORKS

THE USUAL AMAZING LAST IMAGE
Philips Capella 753/4E/3D
giovanni